facebook Google+ twitter flickr youtube in crestron
Produktkategorien
Produkt
Produktfoto

AMP-2210S

Audio Verstärker 2 x 210 Watt

Audio Verstärker CLASS D, 19“ breit, 1 HE hoch, 2 x 210 Watt an 4 Ohm, bzw. 2 x 120 Watt an 8 Ohm, automatische Abschaltung, wenn kein Signal anliegt sowie Zuschaltung bei Signalerkennung, lüfterlose Bauweise, geringer Klirrfaktor, drei Fernsteuerkontakte.

Crestron® AMP-series Commercial Power Amplifiers provide a perfect combination of high output and efficiency for all types of professional audio applications. 100% Crestron engineered and built, these amplifiers are ENERGY STAR® qualified to enable organizations to fulfill their green initiatives without compromising on audio performance. Advanced design features include a high-efficiency amp topology with active power factor corrected power supply, delivering a generous amount of power in a space-saving 1U rack-mountable chassis.

The AMP-2210S provides two channels of amplification. Each channel is rated for 210W @ 4Ω or 120W @ 8Ω, and may be bridged together to deliver a robust 420W @ 8Ω to a single load.

ENERGY STAR® Qualified
Its ultra-efficient design allows the AMP-2210S to meet demanding ENERGY STAR qualification requirements, affording a cost-reducing solution for boardrooms, auditoriums, and other commercial systems. Auto power-down places the amplifier into a low-power standby state if no input signal is detected for 30 minutes. The amplifier quickly powers back on the instant an input signal is detected. In addition, each amp channel can be independently enabled or disabled via jumpers or remote contacts, reducing power consumption by shutting down individual channels when they are not needed. Whether switched remotely or through an AC power controller, the AMP-2210S draws no added inrush current during power-up, reducing AC circuit requirements and potentially eliminating the need for extra power sequencing equipment.

Professional System Integration
The AMP-2210S includes professional balanced inputs with rear-panel ±10dB input level adjustments to assure compatibility with a wide range of audio sources. Remote power control is enabled for each channel using external contact closures, switches, or control system relays. All input, output, and remote control connections are facilitated via detachable screw-terminal connectors to simplify installation and servicing.

Cool and Compact
The AMP-2210S features a durable, lightweight chassis that may be placed on a shelf, or rack-mounted using the rack ears provided. At only one rack space high and under 11 inches deep, it is ideal for installations requiring a lot of power in a limited space. Its efficient, cool-running design gives off substantially less heat than comparably rated amplifiers. Convection cooling means there are no noisy fans, allowing the AMP-2210S to be installed in a boardroom lectern or credenza without affecting noise levels.

Rugged and Dependable
All AMP-series amplifiers are designed for ultimate dependability in a wide range of commercial environments. Built-in over current and DC offset protection on each channel helps prevent damage to the amplifier and speakers due to external or internal faults. Discrete thermal protection is also provided on each channel and the power supply. Front panel indicators are provided for each channel to show signal presence, clipping, and fault conditions.

Key Features

 

  • ENERGY STAR® qualified power amplifier
  • Ultra-efficient space-saving design
  • Low total cost of ownership
  • High-output power, low noise, low distortion performance
  • Two channels each rated 210W@4Ω and 120W@8Ω
  • Bridgeable for 420W@8Ω
  • Individual channel power control via jumper or remote contact
  • Auto power-down after 30 minutes of no signal
  • Instant auto power-on when an input signal is detected
  • No inrush current during power-up
  • Over current and DC offset protection per output
  • Thermal protection on the power supply and each channel
  • Front panel signal, clip, and fault indicators per channel
  • Professional balanced inputs
  • Detachable terminal block connectors
  • Rear panel ±10dB input level controls
  • Convection cooled - no noisy fans
  • Single-space 1U rack mountable
  • Lightweight and under 11 inches deep
  • Universal power supply with active power factor correction

Notes:

    This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

    Specifications subject to change without notice. Crestron is not responsible for errors in typography or photography.

    Crestron and the Crestron logo are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other countries. ENERGY STAR is either a trademark or registered trademark of the United States Environmental Protection Agency in the United States and/or other countries. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. ©2011 Crestron Electronics, Inc.

Audio
  • Typical of 2 mono amplifier channels:
  • Input Signal Type Balanced or unbalanced analog line-level
    Output Signal Type 4/8 Ohm
    Output Power 120 Watts at 8 Ohms;
    210 Watts at 4 Ohms;
    420 Watts at 8 Ohms bridged
    Damping Factor >100
    Protection Over Current, Over/Under Voltage, Over Temperature, DC Offset
    Frequency Response 20Hz to 20kHz ±0.5 dB
    THD 0.05% @ 1kHz, full rated power at 4/8 Ohms or 8 Ohms Bridged;
    0.1% @ 20Hz to 20kHz, 120W at 8 Ohms;
    0.2% @ 20Hz to 20kHz, 210W at 4 Ohms;
    0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged
    S/N Ratio >103 dB, A-weighted
    Crosstalk >70 dB @ 1kHz
    Gain 23 dB with INPUT LEVEL control set at 12 o'clock nominal position
    Input Sensitivity 2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o'clock nominal position
    Input Detection Threshold 40 mV RMS @ 1 kHz
    Input Level Adjustment ±10 dB from nominal
    Connectors
    G 6-32 screw, chassis ground lug
    INPUT CH 1 – 2 (2) 3-pin 3.5mm detachable terminal blocks;
    Balanced/unbalanced line-level audio inputs;
    Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position;
    Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced
    SPEAKER OUTPUT CH 1 – 2 (2) 2-pin 7.62mm 15A detachable terminal blocks;
    4Ω/8Ω and 70/100V power amplifier outputs;
    Wire Size: Terminals accept up to 14 AWG
    REMOTE (1) 6-pin 3.5mm detachable terminal block;
    Provides (2) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures;
    inputs may be safely paralleled for global control
    FUSE T6.3AH 250V Main fuse holder;
    5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated
    100-240V~50/60Hz (1) IEC C14 male chassis plugs, main power input;
    Mates with removable power cord (included)
    Controls & Indicators
    PWR (1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state
    INPUT 1 – 2, SIGNAL (2) green LEDs, indicate signal presence on each corresponding channel
    OUTPUT 1 – 2, CLIP (2) amber LEDs, indicate a clipping condition on each corresponding channel
    OUTPUT 1 – 2, FAULT (2) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel
    INPUT CH 1 – 2 LEVEL (rear) (2) Rotary input boost/attenuate adjustments w/center detent at nominal
    ON/REMOTE/OFF (rear) (1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel
    Power Requirements
    Main Power 100-240 Volts AC, 50/60 Hz
    Power Consumption 62 Watts @ 8 Ohms, all channels driven at 1/8th output power;
    88 Watts @ 4 Ohms, all channels driven at 1/8th output power;
    26 Watts, all channels idle;
    <1 Watt in standby
    Environmental
    Temperature 41° to 104°F (5° to 40°C)
    Humidity 10% to 90% RH (non-condensing)
    Heat Dissipation 110 BTU/Hr @ 8 Ohms, all channels driven at 1/8th output power;
    121 BTU/Hr @ 4 Ohms, all channels driven at 1/8th output power;
    89 BTU/Hr, all channels idle;
    <3.4 BTU/Hr in standby
    Enclosure
    Chassis Metal with black finish, vented top and sides, convection cooled
    Front Panel Metal, black finish with polycarbonate label overlay
    Mounting Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included)
    Dimensions
    Height 1.70 in (44 mm)
    Width 17.28 in (439 mm);
    19.0 in (483 mm) with rack ears
    Depth 10.34 in (263 mm)
    Weight
    8.1 lb (3.7 kg)

    Publications

    Spec Sheet

    Spec Sheet (PDF - 968 K)
    Rev. Date: 10/3/2011

    Installation and Operations Guide

    Installation And Operations Guide (PDF - 2.78 M)
    Doc. No. 7251A
    Rev. Date: 10/17/2011

    CADs, Drawings and Revit Files

    Zoomable Drawing

    Zoomable Drawing

    Cad Files

    Cad Files (ZIP - 556 K)
    Rev. Date: 9/13/2011

    Available Models

    Model Description

    AMP-2210S

    2x210W Commercial Power Amplifier, 4/8Ω

     

     

     

    Invitation to Tender

    AMP-2210S (TXT - 1.8 KB)
    Letzte Änderung 11.11.2012