facebook Google+ twitter flickr youtube in crestron
Produktkategorien
Produkt
Produktfoto

DIN-2MC2

2-Kanal-Motormodul

2 Kanal Motormodul für 230V Motoren. Eingebaute, mechanische Verriegelung für AUF/AB bzw. ÖFFNEN/SCHLIESSEN. Zur Steuerung von Beschattungen, Jalousien, Liften, Leinwänden, Verdunklungen…. Cresnet Anschluss, frontseitige Handbedienung und Anzeige der Cresnet ID, Override Eingang. Format 6 TE.

The DIN-2MC2 is a 2-channel motor control module designed to provide control of bidirectional motors for drapes, shades, projection screens, lifts, skylights, and gates. Each channel supports up/down or open/close control of a conventional three-wire bidirectional type motor up to 1/2 HP at voltages up to 240 Volts. Built-in timing and interlock logic make it easy to program the DIN-2MC2 for failsafe operation.

Override Input
An override input is provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset state. States can be set and saved locally from the front panel, or remotely via software.

DIN Rail Installation
The DIN-2MC2 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-2MC2's front panel stays accessible while the connections are concealed.

Cresnet®
The DIN-2MC2 communicates with a DIN-AP2 2-Series Automation Processor, or other Crestron 2-Series control system, via the Cresnet control network. A pair of Cresnet ports is provided on the DIN-2MC2 allowing for easy daisy-chaining of several DIN Rail Series automation control modules.

Key Features

 

  • Dual-channel bidirectional motor control
  • Supports 120 to 240 Volt 50/60 Hz
  • Override input
  • Cresnet communications
  • Setup via front panel or software
  • Programmable functionality via DIN-AP2
  • 6M wide DIN rail mounting

Load Ratings
  Motor Control Channels 2
  Per Channel 0.5 HP @ 240 Volts AC, 50/60 Hz
  Module Total 1 HP @ 240 Volts AC, 50/60 Hz
  Load Types 3-Wire bidirectional motors
Connections
  1 – 2 (2) sets of (3) captive screw terminals;
3-wire bidirectional motor control relays;
Maximum Wire Size: 12 AWG (2.5 mm²)
  NET (2) 4-pin 3.5mm detachable terminal blocks, paralleled;
Cresnet slave port
  OVERRIDE (2) 2-pin 3.5mm detachable terminal blocks, paralleled;
Sensing input for external low-voltage contact closure;
Activates override mode when a closure is present;
Minimum Closure Rating: 10mA (per module) at 24 Volts
Controls & Indicators
  OPEN & CLOSE 1 – 2 (4) Red LEDs and (4) miniature pushbuttons for status indication and local control of each channel
  NET ID (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID
  SETUP (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
  OVR (1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets
  PWR (1) Green LED, illuminates when DC power is applied to the NET port
  NET (1) Yellow LED, indicates communication with the control processor
  RESET (1) Recessed miniature pushbutton, resets internal processor
Enclosure
  Light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated, 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 6 DIN module spaces (108mm)
Power Requirements
  Cresnet Power Usage 3 Watts (1.13 Amps @ 24 Volts DC)
Environmental
  Temperature 32° to 104°F (0° to 40°C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 10 BTU/hr
Dimensions
  Height 3.71 in (9.42 cm)
  Width 4.18 in (10.60 cm)
  Depth 2.35 in (5.95 cm)
Weight
  7.4 oz (210 g)

Typical DIN-2MC2 Application
Models Included: DIN-2MC2

Shows typical connections to and from a DIN-2MC2.

Application Diagram (PDF - 611 K)
Rev. Date: 7/8/2008

Application Diagram

Publications

Spec Sheet

Spec Sheet (PDF)

Installation and Operations Guide

Installation And Operations Guide (PDF - 2.17 M)
Doc. No. 6665B
Rev. Date: 5/4/2010

Engineering Specs

Engineering Specs (PDF - 293 K)
Rev. Date: 10/31/2008
Note: This document covers the DIN Rail lighting control products series.

CADs, Drawings and Revit Files

Zoomable Drawing

Zoomable Drawing

Cad Files

Cad Files (ZIP - 506 K)
Rev. Date: 10/17/2012

Available Models

Model Description      

DIN-2MC2

DIN Rail Motor Control, 2 feeds, 2 channels

 

 

 

Invitation to Tender

DIN-2MC2 (TXT - 1.27 KB)
Letzte Änderung 13.01.2014