facebook Google+ twitter flickr youtube in crestron
Produktkategorien
Produkt
Produktfoto

CLS-EXP-DIMU

Leistungsverstärker Phasenan- & abschnitt

Wie CLS-EXP-DIM, nur ausgelegt für Phasenanschnitt und Phasenabschnitt.

The CLS-EXP-DIMU enables the expansion of Crestron iLux™ Integrated Lighting System (CLS-C6 series) and other Crestron lighting dimmers to allow dimming of both forward and reverse phase type loads. Supported loads include LED¥, electronic low-voltage, magnetic low-voltage, incandescent, neon/cold cathode, or 2-wire dimmable fluorescent. A single model supports 120, 230, or 277 Volt loads up to 16 Amps.

The CLS-EXP-DIMU simplifies installation by auto-detecting the dimmable load type connected to it and selecting the appropriate operating mode to control that load. Reverse phase (trailing edge) mode supports incandescent and electronic low-voltage load types, while forward phase (leading edge) mode handles magnetic low-voltage, neon, and other inductive load types.

Any output channel of the iLux system can be used to control the CLS-EXP-DIMU to dim a fully loaded circuit. It is also compatible with CLW-Series* in-wall dimmers and select CLX-Series lighting control modules†. The metal enclosure is designed for mounting to a vertical surface‡, and can be installed in an environmental air-handling space above a suspended ceiling. Conduit knockouts are provided on the bottom and lower sides. All connections are made via screw terminals behind the front cover.

¥ For a list of compatible ballasts, visit www.crestron.com/lightingcompatibility (PDF)

Key Features

 

  • Works with Crestron iLux, CLW*, and CLX series dimmers
  • Works with the DIN-1DIMU4 dimmer
  • Emulates the characteristics of the dimmer that is controlling it
  • Up to 5 Expansion Modules can be connected to a single iLux dimmer channel
  • Supports 120, 230, and 277 Volt LED¥, ELV, MLV, NCC, incandescent, and 2-wire dimmable fluorescent loads
  • Auto-selects for forward or reverse phase
  • Includes threshold adjustment for setting minimum fluorescent dimming level
  • Built-in air gap relay at the output
  • Mounts to a wall or above a suspended ceiling

Load Ratings
  Dimmer Channels 1
  Load Rating 16 Amps
  Minimum Load 50 Watts
  Load Types LED¥, electronic low voltage, incandescent, neon/cold cathode, magnetic low voltage, 2-wire dimmable fluorescent (Advance Mark 10 Powerline® or equivalent)
Input Voltages
  Line Power 120 to 277 Volts AC, 50/60 Hz
  Control Input 120 or 230 Volts AC, 50/60 Hz, phase independent of line power and load
Connections
  INPUT, CTRL (1) Captive screw terminal§, control input from CLS(I)-C6 Series, CLW-DIM Series*, CLX(I)-DIM Series, GLX-DIM6, GLXX-2DIM8, DIN-1DIM4, or DIN-1DIMU4 dimmers;
Note: Presents a 25 Watt load to the controlling dimmer; a maximum of 5 CLS-EXP-DIMU modules may be connected to the controlling dimmer, which cannot be wired to control any other loads besides the CLS-EXP-DIMU modules
  INPUT, NEUT (1) Captive screw terminal§, neutral connection for control input
  OUTPUT, DIM OUT (1) Captive screw terminal§, dimmed load output
  OUTPUT, HOT (1) Captive screw terminal§, line power input
  OUTPUT, NEUT (1) Captive screw terminal§, neutral connection for line power input and load
  GROUND (1) 3-terminal chassis ground bus bar
Controls & Indicators
  FLUORESCENT OFF THRESHOLD (1) recessed screwdriver-adjustable trim pot behind removable cap, adjusts minimum brightness level
  PHASE (1) Yellow LED behind front panel, illuminates when operating in reverse-phase mode
  STATUS (1) Red LED behind front panel, illuminates when load output is on
  POWER (1) Green LED behind front panel, indicates line power is applied to the HOT terminal
  S1 (1) 2-position DIP switch behind front panel, enables/disables zero-cross detection filter
  S2 (1) 2-position DIP switch behind front panel; selects forward, reverse, or auto-detect dimming mode
Enclosure
  Surface mount‡ module with (2) integral mounting flanges, galvanized steel w/gray matte powder coat front panel, extruded aluminum heat sink, (4) 1/2” or 3/4” conduit knockouts provided on bottom and lower left & right sides
Environmental
  Temperature 32° to 104°F (0° to 40°C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 200 BTU/Hr at maximum load, 16A
Dimensions
  Height 8.82 in (22.40 cm)
  Width 6.39 in (16.23 cm)
  Depth 3.18 in (8.08 cm)
Weight
  3.34 lb (1.52 kg)

¥ For a list of compatible ballasts, visit www.crestron.com/lightingcompatibility (PDF)

* CLW-Series device must have a dedicated neutral.

Compatible only with forward-phase dimming modules.

Must be oriented upright, mounted to a vertical surface, with 6 inches (15 cm) minimum spacing above and below for proper ventilation and heat dissipation.

§ Captive screw terminals accept up to two 22 to 12 AWG (0.34 to 4.0 mm2) wires per terminal.

Typical CLS-EXP-DIM Connections
Models Included: CLS-EXP-DIM, CLS-EXP-DIMFDB, CLS-EXP-DIMFLV, CLS-EXP-DIMU

Shows typical connections to and from a CLS-EXP-DIM, CLS-EXP-DIMU, CLS-EXP-DIMFLV and CLS-EXP-DIMDB.

Application Diagram (PDF - 532 K)
Rev. Date: 2/12/2008

Application Diagram

Publications

Spec Sheet

Spec Sheet (PDF - 766 K)
Rev. Date: 3/15/2012

Manual

Manual (PDF - 1.43 M)
Doc. No. 6682C
Rev. Date: 5/4/2012

CADs, Drawings and Revit Files

Zoomable Drawing

Zoomable Drawing

Cad Files

Cad Files (ZIP - 1.2 M)
Rev. Date: 10/17/2012

Revit Files

Revit (ZIP - 561 K)
Rev. Date: 8/30/2011

Available Models

Model Description      

CLS-EXP-DIMU

iLux™ Universal Dimmer Expansion Module

 

 

 

Invitation to Tender

CLS-EXP-DIMU (TXT - 692 B)
Letzte Änderung 11.11.2012