facebook Google+ twitter flickr youtube in crestron
Kontakt:  +49 731 96281-0


DALI Interface

Interface mit 2 unabhängigen DALI Linien. Für DALI-Betriebsgeräte. Steuert pro Linie 64 DALI Adressen,16 Szenen,16 Gruppen pro Linie. Stromversorgung für den DALI-Systembus ist integriert. Zusätzliche Override Funktion. Einfache Inbetriebnahme des Interfaces durch Crestron Software. Format 9 TE. Stromversorgung des Modules über PoE oder Cresnet.

The DIN-DALI-2 is a DALI® interface for Crestron® systems that provides control of up to 2 individual DALI loops. Housed in a DIN-rail enclosure, the DIN-DALI-2 is a great low-profile Cresnet® or Ethernet companion to the DIN-AP3 processor or any 3-Series® control system. In addition to controlling the DALI data bus, it includes an integrated DALI power supply. Single-wire connectivity simplifies both new and retrofit installations, and Power-over-Ethernet (PoE) versatility assists in situations with existing CAT5 infrastructure.

Two DALI Channels
The dual-channel DALI outputs on the DIN-DALI-2 makes controlling up to 128 individual DALI ballasts easy. The Digital Addressable Lighting Interface (DALI) is a protocol used for the control of lighting in buildings and is found on ballasts available from many manufacturers. Since it offers ballast-level control, lighting loads powered from the same feed can be controlled individually. DALI is a great choice for retrofit lighting systems because it does not require changes in line voltage wiring. Likewise, DALI provides ultimate flexibility by allowing reconfiguring of zones after a system is installed.

Integrated DALI Power Supply
The innovative design of the DIN-DALI-2 eliminates the need for the external power supplies required by other DALI controllers on the market. Power is delivered via PoE or Cresnet[1], creating a true single-wire installation. Both Cresnet and PoE are capable of powering all 128 DALI ballast controllers. If desired, an external power supply may be used in conjunction with the DIN-DALI-2. An on-board switch allows the installer to choose the required mode during setup.

Commissioning Tool
Designed specifically for the DIN-DALI-2, the Crestron DALI commissioning software tool facilitates system setup. The intuitive menu-driven wizard provides step-by-step configuration of ballast properties, groups, and scenes. Guided by the software, one can simply set the ballast address and check connectivity status, edit minimum/maximum levels and fade time, and change ballast groupings and scenes. This powerful software makes ballast replacement straightforward through automatic identification of new hardware IDs. Settings from old ballasts are transferred to replacements with just a few mouse clicks, saving time and eliminating guess work and frustration.

Familiar Programming Interface
Controlling a DALI ballast is just like controlling any Crestron dimmer. Familiar visual Crestron configuration tools, as found in D3 Pro® and SIMPL™ Windows, replace complex hardware addressing and communication protocols. Crestron D3 Pro software eliminates the need for custom programming, providing a complete design, development, and documentation solution for the lighting professional.

Override Input
An override input is provided to allow an external contact closure to momentarily override the control system program and force each ballast into its defined "System Failure Level." States can be set and saved locally from the front panel, or remotely via software.

DIN Rail Installation
The DIN-DALI-2 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When the DIN-DALI-2 is installed in an enclosure utilizing 45 mm cutouts, the front panel stays accessible while the connections are concealed.

Cresnet® and PoE
The DIN-DALI-2 communicates with a DIN-AP3 Automation Processor, or other Crestron 3-Series control systems, via the Cresnet control network or Power-over-Ethernet (PoE). A pair of Cresnet ports on the DIN-DALI-2 allows for easy daisy-chaining of several DIN Rail Series automation control modules. A standard Ethernet jack accommodates data and power to be delivered to the unit over one CAT5 cable.

Key Features


  • Interfaces with 2 independent DALI® loops
  • Controls up to 128 DALI ballasts
  • Cresnet® or PoE communication for single-wire installation
  • Integrated DALI power supply
  • Crestron® DALI commissioning tool for easy setup
  • Override input
  • 9M wide DIN rail mounting
  • CEC Title 24 2013 Compliant


  1. The DIN-DALI-2 may be powered by PoE or Cresnet network power. Unit will default to Cresnet power if both are present.

This product may be purchased from an authorized Crestron dealer. To find a dealer, please contact the Crestron sales representative for your area. A list of sales representatives is available online at www.crestron.com/salesreps or by calling 800-237-2041.

The specific patents that cover Crestron products are listed online at: patents.crestron.com.

Crestron, the Crestron logo, 3-Series, Cresnet, Crestron Green Light, D3 Pro, and SIMPL+ are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. DALI is either a trademark or registered trademark of ZVEI - Zentralverband Elektrotechnik- und Elektronikindustrie in the United States and/or other countries.Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography. Specifications are subject to change without notice. ©2014 Crestron Electronics, Inc.

  NET (2) 4-pin 3.5mm detachable terminal blocks, paralleled;
Cresnet® slave port
  OVERRIDE (2) 2-pin 3.5mm detachable terminal blocks, paralleled;
Sensing input for external low-voltage contact closure;
Activates override mode when a closure is present, forces each ballast into its defined "System Failure Level";
Minimum Closure Rating: 10mA (per module) at 24 Volts
  LAN PoE (1) 8-wire RJ45 with 2 LED indicators;
10BaseT/100BaseTX Ethernet port;
802.3af Power over Ethernet compliant;
Green LED indicates link status;
Yellow LED indicates Ethernet activity
  DALI® 1, 2 (2) 2-pin 5mm terminal blocks;
Each set of (+) and (-) is paralleled with the adjacent like ports on the same channel;
Each channel controls a single DALI loop (up to 64 ballasts);
3kVAC isolation between Cresnet/Ethernet ports;
Wire Gauge: 28 AWG to 12 AWG
  COMPUTER (1) USB Type B female, USB 1.1 computer console port
Controls & Indicators
  TEST (2) Yellow LEDs and (2) miniature pushbuttons for testing on/off and dim up/down for all attached ballasts in channel
  DALI POWER (1) 2-position switch, sets DALI power between internal (INT) and external (EXT);
When set to "INT" DALI uses power supplied by the DIN-DALI-2;
When set to "EXT" DALI uses power provided by external power supply (not included)
  NET ID (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID
  SETUP (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
  OVR (1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets
  PWR (1) Green LED, illuminates when DC power is applied to the NET port
  NET (1) Yellow LED, indicates communication with the control processor
  RESET (1) Recessed miniature pushbutton, resets internal processor
  Light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated, 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 9 DIN module spaces (162mm)
Power Requirements[1]
  PoE Power Usage IEEE 802.3af (802.3at Type 1) Class 0 PoE Powered Device;
capable of powering up to 128 DALI ballast controllers
  Cresnet Power Usage 9 watts (0.375 Amps @ 24 Volts DC), DALI POWER switch set to "INT";
2 Watts (0.08 Amps @ 24 Volts DC), DALI POWER switch set to "EXT";
capable of powering up to 128 DALI ballast controllers
  Temperature 32° to 104°F (0° to 40°C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 44 BTU/hr
  Height 3.71 in (95 mm)
  Width 6.26 in (159 mm)
  Depth 2.35 in (60 mm)
  9.58 oz (272 g)
Standards & Certifications
  UL Listed, CE, CEC Title 24 2013 Compliant


Spec Sheet

Spec Sheet (PDF - 933 K)

Design Guide

Design Guide (PDF - 8.24 M)
Doc. No. 7386E
Rev. Date: 4/9/2015
Note: DALI Lighting Design Guide. This design guide provides detailed information on the Digital Addressable Lighting Interface (DALI) systems.

Installation and Operations Guide

Installation And Operations Guide (PDF - 252 K)
Doc. No. 6968D
Rev. Date: 3/4/2015

Programming Guide

Programming Guide (PDF - 1.05 M)
Doc. No. 7365A
Rev. Date: 4/11/2013

Engineering Specs

Engineering Specs (.DOCX - 77 K)
Rev. Date: 12/15/2014
Note: CSI Guide Specification for Lighting Control System

Engineering Specs

Engineering Specs (PDF - 130 K)
Engineering Specs (.DOC - 83 K)
Rev. Date: 9/23/2010
Note: For Crestron Green Light® Architectural Dimming Systems DALI. Construction Specifications Institute documents for architects, engineers, specifiers and contractors.

Engineering Specs

Engineering Specs (PDF - 117 K)
Engineering Specs (.DOCX - 41 K)
Rev. Date: 4/26/2012
Note: SECTION 26 51 13 - INTERIOR LIGHTING FIXTURES, LAMPS, AND BALLASTS. For Crestron Controllable Dimming Ballasts.

CADs, Drawings and Revit Files

Zoomable Drawing

Zoomable Drawing

Cad Files

Cad Files (ZIP - 295 K)
Rev. Date: 7/29/2010

Revit Files

Revit (ZIP - 737 K)
Rev. Date: 8/29/2011

Invitation to Tender

DIN-DALI-2 (TXT - 1.13 KB)
Letzte Änderung 30.09.2014