| Input/Output Modes |
| |
Essex Panel Mode |
(5) pulse inputs from Essex keypad plus (1) contact closure input and (8) electronic closure/24VDC outputs |
| |
Button Matrix Mode |
4 X 4 switch matrix plus (2) contact closure inputs and (4) electronic closure/24VDC outputs |
| |
Discrete I/O Mode |
(6) contact closure inputs and (8) electronic closure/24VDC outputs |
| Audio – Speaker |
| |
Amplifier Output Power |
13 watts at 8 ohms |
| |
Volume Gain Range |
-80dB to +20dB, 1.0dB steps |
| |
Mute |
Electronic |
| |
Bass Gain Range |
±14dB, 2.0dB steps |
| |
Treble Gain Range |
±14dB, 2.0dB steps |
| |
Frequency Response |
100Hz to 20kHz, ±1dB |
| |
THD+N |
<0.5% @ 100Hz to 20kHz, full output |
| |
S/N Ratio |
80dB @ 1kHz, full output |
| Audio – Microphone |
| |
Frequency Response |
20Hz to 20kHz, ±0.5dB |
| Audio – WAV File |
| |
Storage Capacity |
30 WAV files maximum, 30 seconds total time |
| |
WAV File |
8-bit PCM, mono, 8 kHz sampling rate |
| |
Volume Gain Range |
-80dB to +20dB, 1.0dB steps |
| |
Bass Gain Range |
±14dB, 2.0dB steps |
| |
Treble Gain Range |
±14dB, 2.0dB steps |
| |
Wav file audio feeds local speaker output only |
| Connectors |
| |
AUDIO |
(1) 8-pin RJ45 female, shielded;
Bidirectional CAT5 balanced audio port;
Maximum Input Level: 4 Vrms;
Output Level: 1 Vrms nominal;
Connects to C2N-IADS30X24, CNX-BIPAD8, CNX-PBAR4, or any “CH” CAT5 audio port** |
| |
VIDEO |
(1) 8-pin RJ45 female, shielded;
CAT5 balanced video output port (composite only);
Output Impedance: 100 ohms;
Output Level: 1 Vp-p nominal;
Connects to C2N-IVDS24X24, CNX-PBVR4, or any “CH” CAT5 video input port** |
| |
AV IO |
(1) 9-pin 3.5mm detachable terminal block comprising:
MIC/GND: Electret microphone input;
Input Level: 34 mV nominal;
Bias Voltage: 5 Volts DC, current limited;
Use Panasonic WM-61B or equivalent electret microphone;
VID IN/GND: Composite video input;
Input Level: 1 Vp-p nominal;
12V/GND: Camera power output;
Maximum Load: 200 mA @ 12 Volts DC;
BELL/GND: Doorbell button input;
Contact closure/logic level input;
Input Voltage: -0.5 to 5.5 Volts DC minimum/maximum;
Logic “1” Threshold: ≥3.2 Volts DC;
Logic “0” Threshold: ≤0.9 Volts DC;
SPK-/+: Speaker-level output;
Output Power: 13 watts @ 8 ohms
|
| |
INPUT |
(1) 12-pin connector comprising (6) contact closure/logic level inputs referenced to GND;
(see “Input/Output Modes” above);
Input Voltage: -0.5 to 5.5 Volts DC minimum/maximum;
Logic "0" Threshold: 3.2 Volts DC maximum;
Logic "1" Threshold: 0.9 Volts DC minimum;
Internal Supply Voltage: +5 Volts DC;
Essex Lamp Control: Switched voltage output for keypad backlight;
Connect to Essex keypad, custom panel, or sensor using 12-inch long cable provided |
| |
OUTPUT |
(1) 14-pin connector comprising (8) electronic closures or switched 24 Volt DC output drivers referenced to GND;
(see “Input/Output Modes” above);
Maximum Load: 50 mA per output;
Maximum External Voltage: 24 Volts DC;
Internal Supply: 500 mA @ 24 Volts DC;
Connect to switched device(s) using 12-inch long cable provided |
| |
NET |
(1) 4-pin 3.5mm detachable terminal block;
Cresnet slave port, connects to Cresnet control network |
| Controls & LED Indicators |
| |
PWR |
(1) green LED, indicates 24 Volts DC power supplied from Cresnet control network |
| |
NET |
(1) yellow LED, indicates communication with Cresnet system |
| |
SETUP (rear) |
(1) recessed miniature pushbutton and (1) red LED, used for touch-settable ID (TSID) |
| |
MIC VOL |
(1) screwdriver-adjustable pot for microphone level adjustment |
| Power Requirements |
| |
Cresnet Power Usage |
20 Watts (1.25 Amps @ 24 Volts DC) plus up to 12 Watts (0.5 Amps) additional if using switched 24 Volt DC outputs |
| Environmental |
| |
Temperature |
-22° to 140°F (-30° to 60°C) |
| |
Humidity |
10% to 90% RH (non-condensing) |
| Enclosure |
| |
Black metal, surface mount box with (2) integral mounting flanges |
| Dimensions |
| |
Height |
5.14 in (13.06 cm) |
| |
Width |
2.74 in (6.96 cm) |
| |
Depth |
1.48 in (3.76 cm) |
| Weight |
| |
13.3 oz (0.38 kg) |
