DIN-1DIM4

4-Kanal-Phasenanschnittdimmer

4-Kanal-Dimmer Phasenanschnitt. Erkennung der Phasensynchronität durch eingebauten Wilson- Filter. Gehäuse für Hutschienenmontage. Maximalleistung 2,3 kW, max. 1150 W je Kanal. Cresnet Anschluss, frontseitige Handbedienung und Anzeige der Cresnet ID, Override Eingang. Format 12 TE.

Beschreibung
Daten
Downloads
Modelle & Zubehör
Ausschreibungstexte

The DIN-1DIM4 is a DIN rail mounted lighting control module with four channels of dimming. A single model supports both 120 and 220-277 Volt electronic and magnetic low-voltage, incandescent, neon/cold cathode, 2-wire dimmable fluorescent, and non-dimmable lighting loads up to 5 Amps per channel, 10 Amps total.

Phase-Synchronous Detection
Circuitry—Crestron's proprietary zero cross filter technology provides superior immunity to noise on the power line, reducing lamp flicker and compensating for fluctuations in line voltage and frequency.

Master Air-Gap Relay
When all four channels are turned fully off, the internal master relay automatically opens providing air-gap isolation to allow safe servicing and changing of light bulbs on all four controlled circuits.

Override Input
An override input is provided to allow an external contact closure to momentarily override the control system program and set each channel output to its override preset level. Levels can be adjusted and saved locally from the front panel, or remotely via software.

DIN Rail Installation
The DIN-1DIM4 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure. Wiring connections are made using screw terminals positioned along the bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-1DIM4's front panel stays accessible while the connections are concealed.

Cresnet®
The DIN-1DIM4 communicates with a DIN-AP2 2-Series Automation Processor, or other Crestron 2-Series control system, via the Cresnet control network. A pair of Cresnet ports is provided on the DIN-1DIM4 allowing for easy daisy-chaining of several DIN Rail Series automation control modules.

4 channels of dimming
120 to 277 Volt 50/60 Hz operation Selectable non-dim mode
Master air-gap relay
Override input
Cresnet communications
Setup via front panel or software
Programmable functionality via DIN-AP2
12M wide DIN rail mounting

Load Ratings
	Dimmer Channels	4
	Maximum Per Channel	5 Amps @ 120 to 277 Volts AC, 50/60 Hz; 600 Watts @ 120 Volts AC; 1150 Watts @ 230 Volts AC; 1200 Watts @ 240 Volts AC 1385 Watts @ 277 Volts AC
	Module Total	10 Amps @ 120 to 277 Volts AC, 50/60 Hz; 1200 Watts @ 120 Volts AC; 2300 Watts @ 230 Volts AC; 2400 Watts @ 240 Volts AC 2770 Watts @ 277 Volts AC
	Load Types	Leading edge ELV, Incandescent, Neon/Cold Cathode, Magnetic Low Voltage, Dimmable 2 Wire Fluorescent, & Non-Dim Lighting
Input Voltage
	Line Power	120 to 277Volts AC, 50/60 Hz
Connections
	NET	(2) 4-pin 3.5mm detachable terminal blocks, paralleled; Cresnet slave port
	OVERRIDE	(2) 2-pin 3.5mm detachable terminal blocks, paralleled; Sensing input for external low-voltage contact closure; Activates override mode when a closure is present; Minimum Closure Rating: 10mA (per module) at 24 Volts
	LIVE	(2) Captive screw terminals†, brown; Line power input
	NEUTRAL	(5) Captive screw terminals†, blue
	DIMMED LIVE 1 – 4	(4) Captive screw terminals†, red; Dimmer channel outputs 1 - 4
	Ground	(5) Captive screw terminals†, green
Controls & Indicators
	NET ID	(2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID; digits also display output levels and protection/error codes
	SETUP	(1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
	OVR	(1) Red LED and (1) miniature pushbutton for enabling override mode and saving override presets
	PWR	(1) Green LED, normally indicates AC line power is connected to either LIVE terminal, blinks when only powered by Cresnet
	NET	(1) Yellow LED, indicates communication with the control processor
	RESET	(1) Recessed miniature pushbutton, resets internal processor
	DIM 1 – 4	(4) Red LEDs, illuminate when a corresponding channel is operating in forward-phase mode
	NON-DIM 1 – 4	(4) Red LEDs, illuminate when a corresponding channel is operating in non-dim mode
	Channel Mode Select 1 – 4	(4) Recessed miniature pushbuttons, used to select each channel’s operating mode
	LOADS 1 – 4	(4) Red LEDs and (4) miniature pushbuttons for status indication and local control of each channel
Enclosure
	Aluminum with polycarbonate label overlay, 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 12 DIN module spaces (216mm)*
Power Requirements
	Cresnet Power Usage	0.6 Watts (0.03 Amps @ 24 Volts DC) when line power is not available
Environmental
	Temperature	32° to 104°F (0° to 40°C)
	Humidity	10% to 90% RH (non-condensing)
	Heat Dissipation	60 BTU/hr @240 Volts with 2 channels 50 BTU/hr @ 120 Volts with 2 channels 52 BTU/hr @ 120 Volts with 2 channels
Dimensions
	Height	3.71 in (9.42 cm)
	Width	8.49 in (21.55 cm)
	Depth	2.35 in (5.95 cm)
Weight
	2.1 lb (912 g)

* Unit dissipates significant heat when fully loaded and should be mounted in an enclosure that is sufficiently ventilated to maintain an ambient temperature not exceeding 104°F (40°C). Maintain 4 inches (10 cm) minimum spacing above and below for proper ventilation and heat dissipation, 6 inches (15 cm) spacing recommended.

Captive screw terminals accept up to 12 AWG (2.5 mm²) wires per terminal.

	Spec Sheet (PDF)
	Installation And Operations Guide (PDF - 3.3 M) Doc. No. 6928A Rev. Date: 2/17/2010

Zoomable Drawing

Cad Files (ZIP - 305 K)
Rev. Date: 10/17/2012

Model	Description
DIN-1DIM4	DIN Rail Dimmer, 1 feed, 4 channels

DIN-1DIM4 (TXT - 1.06 KB)
Letzte Änderung 11.11.2012