facebook Google+ twitter flickr youtube in crestron
Produktkategorien
Produkt
Produktfoto

DIN-IO8

8 –fach Ein- bzw. Ausgangsmodul

8-fach Ein- bzw. Ausgangsmodul (8 Versiports). Digitale Eingänge und Ausgänge für bis zu 24 Volt DC, Analoge Eingänge 0-10 Volt DC. Frontseitige Statusanzeige für jeden I/O Port, Frontseitige Anzeige / Einstellmöglichkeit der Cresnet ID. Zum Anschluss von Kontaktgebern wie Taster, Schalter, Alarmkontakte, Wasserstandsmeldern, Potentiometer, Windwächter, Temperatursensoren. Format 6 TE.

The DIN-IO8 is a DIN rail-mounted automation control module that provides eight Versiport I/O ports for interfacing with a wide range of third-party devices and systems. Each "Versiport" can be configured via software to function as a digital or analog sensing input, or as a digital trigger output.

Versiports
Configured as a digital input, the Versiport will sense a contact closure or logic level signal from devices such as motion detectors, partition sensors, alarm panels, 12V triggers, and all types of switches and relays. As an analog input, the Versiport can sense changes in a resistance or DC voltage level, working with everything from temperature and light sensors to water level meters to volume control potentiometers. As a digital output, the Versiport provides a logic level closure signal to trigger control and alarm inputs on a variety of external devices.

DIN Rail Installation
The DIN-IO8 is designed to snap onto a standard DIN rail for installation in a wall mount enclosure or mounted on a wall panel. Wiring connections are made using detachable screw terminals positioned along the top and bottom, clearly accessible from the front for easy installation and servicing. All setup controls and indicators are positioned on the center front panel. When installed in an enclosure utilizing 45 mm cutouts, the DIN-IO8's front panel stays accessible while the connections are concealed.

Cresnet®
The DIN-IO8 communicates with a DIN-AP2 2-Series Automation Processor, or other Crestron 2-Series control system, via the Cresnet control network. Cresnet also powers the DIN-IO8. A pair of Cresnet ports is provided on the DIN-IO8 allowing for easy daisy-chaining of several DIN Rail Series automation control modules.

Key Features

 

  • 8 Versiport I/O ports
  • Interface for 3rd-party sensors, detectors, contact closures, and alarms
  • Fully programmable functionality via DIN-AP2
  • Cresnet communications
  • 6M wide DIN rail mounting

Connections
  I/O 1 – 8 (2) 5-pin 3.5mm detachable terminal blocks comprising (8) digital input/output or analog input ports (referenced to GND);
Digital Input: Rated for 0-24 Volts DC, input impedance 20k ohms, logic threshold 1.25 Volts DC;
Digital Output: 250 mA sink from maximum 24 Volts DC, catch diodes for use with “real world” loads;
Analog Input: Rated for 0-10 Volts DC, protected to 24 Volts DC maximum, input impedance 20k ohms;
Programmable 5 Volts, 2k ohms pull-up resistor per pin
  NET (2) 4-pin 3.5mm detachable terminal blocks, paralleled;
Cresnet slave port
Controls & Indicators
  I/O 1 – 8 (8) Red LEDs, indicate status of Versiport I/O ports
  NET ID (2) 7-Segment green LED digits and (2) miniature pushbuttons for setting Cresnet ID
  SETUP (1) Red LED and (1) recessed miniature pushbutton for enabling setup mode and touch-settable ID
  PWR (1) Green LED, illuminates when DC power is applied to the NET port
  NET (1) Yellow LED, indicates communication with the control processor
  RESET (1) Recessed miniature pushbutton, resets internal processor
Enclosure
  Light gray polycarbonate housing with polycarbonate label overlay, UL94 V-0 rated, 35mm DIN EN 60715 rail mount, DIN 43880 form factor for enclosures with 45mm front panel cutout, occupies 6 DIN module spaces (108mm)
Power Requirements
  Cresnet Power Usage 1.5 Watts (0.06 Amps @ 24 Volts DC)
Environmental
  Temperature 32° to 104°F (0° to 40°C)
  Humidity 10% to 90% RH (non-condensing)
  Heat Dissipation 5 BTU/hr
Dimensions
  Height 3.71 in (9.42 cm)
  Width 4.18 in (10.60 cm)
  Depth 2.35 in (5.95 cm)
Weight
  5.9 oz (165 g)

Typical DIN-IO8 Application
Models Included: DIN-IO8

Shows typical connections to and from a DIN-IO8.

Application Diagram (PDF - 702 K)
Rev. Date: 7/8/2008

Application Diagram

Publications

Spec Sheet

Spec Sheet (PDF)

Installation and Operations Guide

Installation And Operations Guide (PDF - 3.3 M)
Doc. No. 6664A
Rev. Date: 5/1/2008

Engineering Specs

Engineering Specs (PDF - 293 K)
Rev. Date: 10/31/2008
Note: This document covers the DIN Rail lighting control products series.

CADs, Drawings and Revit Files

Zoomable Drawing

Zoomable Drawing

Cad Files

Cad Files (ZIP - 522 K)
Rev. Date: 4/21/2008

Available Models

Model Description      

DIN-IO8

DIN Rail Versiport Module

 

 

 

Invitation to Tender

DIN-IO8 (TXT - 1.27 KB)
Letzte Änderung 11.11.2012